Flydumps provides the guaranteed preparation material to boost up your confidence in Cisco 640-802 exam. Successful candidates have provided their reviews about our guaranteed Cisco 640-802 preparation material,you can come to realize the real worth of our featured products through overviewing the reviews and testimonials.
QUESTION 10
What are three characteristics of the OSPF routing protocol? (Choose three.)
A. It converges quickly.
B. OSPF is a classful routing protocol.
C. It uses cost to determine the best route.
D. It uses the DUAL algorithm to determine the best route.
E. OSPF routers send the complete routing table to all directly attached routers.
F. OSPF routers discover neighbors before exchanging routing information.
Correct Answer: ACF Section: (none)Explanation Explanation/Reference:
QUESTION 11
Refer to the graphic. A static route to the 10.5.6.0/24 network is to be configured on the HFD router. Which commands will accomplish this? (Choose two.)
A. HFD(config)# ip route 10.5.6.0 0.0.0.255 fa0/0
B. HFD(config)# ip route 10.5.6.0 0.0.0.255 10.5.4.6
C. HFD(config)# ip route 10.5.6.0 255.255.255.0 fa0/0
D. HFD(config)# ip route 10.5.6.0 255.255.255.0 10.5.4.6
E. HFD(config)# ip route 10.5.4.6 0.0.0.255 10.5.6.0
F. HFD(config)# ip route 10.5.4.6 255.255.255.0 10.5.6.0
Correct Answer: CD Section: (none)Explanation
Explanation/Reference:
QUESTION 12
What should be done prior to backing up an IOS image to a TFTP server? (Choose three.)
A. Make sure that the server can be reached across the network.
B. Check that authentication for TFTP access to the server is set.
C. Assure that the network server has adequate space for the IOS image.
D. Verify file naming and path requirements.
E. Make sure that the server can store binary files.
F. Adjust the TCP window size to speed up the transfer.
Correct Answer: ACD Section: (none) Explanation
Explanation/Reference:
QUESTION 13
What are the possible trunking modes for a switch port? (Choose three.)
A. transparent
B. auto
C. on
D. desirable
E. client
F. forwarding
Correct Answer: BCD Section: (none) Explanation
Explanation/Reference:
QUESTION 14
The network 172.25.0.0 has been divided into eight equal subnets. Which of the following IP addresses can be assigned to hosts in the third subnet if the ip subnet-zero command is configured on the router? (Choose three.)
A. 172.25.78.243
B. 172.25.98.16
C. 172.25.72.0
D. 172.25.94.255
E. 172.25.96.17
F. 172.25.100.16
Correct Answer: ACD Section: (none)Explanation
Explanation/Reference:
QUESTION 15
Refer to the graphic. Host 1 cannot receive packets from Host 2. Assuming that RIP v1 is the routing protocol in use, what is wrong with the IP configuration information shown? (Choose two.)
A. The fa0/1 interface of router R2 has been assigned a broadcast address.
B. The fa0/1 network on router R2 overlaps with the LAN attached to R1.
C. Host 2 has been assigned the incorrect subnet mask.
D. Host 1 has been configured with the 255.255.248.0 subnet mask.
E. Host 2 on router R2 is on a different subnet than its gateway.
Correct Answer: BC Section: (none)Explanation
Explanation/Reference:
QUESTION 16
What are three valid reasons to assign ports to VLANs on a switch? (Choose three.)
A. to make VTP easier to implement
B. to isolate broadcast traffic
C. to increase the size of the collision domain
D. to allow more devices to connect to the network
E. to logically group hosts according to function
F. to increase network security
Correct Answer: BEF Section: (none) Explanation
Explanation/Reference:
QUESTION 17
Refer to the topology shown in the exhibit. Which ports will be STP designated ports if all the links are operating at the same bandwidth? (Choose three.)
A. Switch A – Fa0/0
B. Switch A – Fa0/1
C. Switch B – Fa0/0
D. Switch B – Fa0/1
E. Switch C – Fa0/0
F. Switch C – Fa0/1
Correct Answer: BCD Section: (none)Explanation
Explanation/Reference:
QUESTION 18
Which statements describe two of the benefits of VLAN Trunking Protocol? (Choose two.)
A. VTP allows routing between VLANs.
B. VTP allows a single switch port to carry information to more than one VLAN.
C. VTP allows physically redundant links while preventing switching loops.
D. VTP simplifies switch administration by allowing switches to automatically share VLAN configuration information.
E. VTP helps to limit configuration errors by keeping VLAN naming consistent across the VTP domain.
F. VTP enhances security by preventing unauthorized hosts from connecting to the VTP domain.
Correct Answer: DE Section: (none) Explanation
Explanation/Reference:
QUESTION 19
Which two of these statements are true of IPv6 address representation? (Choose two.)
A. There are four types of IPv6 addresses: unicast, multicast, anycast, and broadcast.
B. A single interface may be assigned multiple IPv6 addresses of any type.
C. Every IPv6 interface contains at least one loopback address.
D. The first 64 bits represent the dynamically created interface ID.
E. Leading zeros in an IPv6 16 bit hexadecimal field are mandatory.
Correct Answer: BC Section: (none) Explanation
Explanation/Reference:
QUESTION 20
What are three basic parameters to configure on a wireless access point? (Choose three.)
A. SSID
B. RTS/CTS
C. AES-CCMP
D. TKIP/MIC
E. RF channel
F. authentication method
Correct Answer: AEF Section: (none)Explanation
Explanation/Reference: Exam I QUESTION 1 Multiple Questions
Which connection uses the default encapsulatation for serial interfaces on Cisco router
A. The serial connection to the Central branch office.
B. The serial connection to the Deep South branch office.
C. The serial connection to the North Central branch office.
D. The serial connection to the Multinational Core.
What destination Layer 2 address will be used in the frame he host 172.30.0.4?
A.767
B.682
C.455
D.46
A static map to the LA-GROUP location is required. Which is this map?
A. frame-relay map ip 172.30.0.3767 broadcast
B. frame-relay map ip 172.30.0.3682 broadcast
C. frame-relay map ip 172.30.0.3455 broadcast
D. frame-relay map ip 172.30.0.346 broadcast
Enter IOS commands on the London router to verify network operation and answer for multiple-choice
questions.
THIS TASK DOES NOT REQUIRE DEVICE CONFIGURATION.
Click on the Console PC to gain access to the console of the ruter No console or enable password are
required.
To access the multiple-choice questions, click on the numbered boxes on the left of the top panel. There are four multiple-choice questions with this task. Be sure to answer all four questions before selecting the Next button.
If required, what password should be configured on the router in the Central branct allow aconnection to be established with the London router?
A. No password is required
B. En8ble
C. Scr8
D. T1net
E. CD nsole
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
Which connection uses the default encapsulatation for serial interfaces on Cisco router
A. The serial connection to the Central branch office.
B. The serial connection to the Deep South branch office.
C. The serial connection to the North Central branch office.
D. The serial connection to the Multinational Core.
Answer: C
What destination Layer 2 address will be used in the frame he host 172.30.0.4?
A.767
B.682
C.455
D.46
Answer: B
A static map to the LA-GROUP location is required. Which is this map?
A. frame-relay map ip 172.30.0.3767 broadcast
B. frame-relay map ip 172.30.0.3682 broadcast
C. frame-relay map ip 172.30.0.3455 broadcast
D. frame-relay map ip 172.30.0.346 broadcast
Answer: B
QUESTION 2
Select and Place:
Correct Answer:
Section: (none)Explanation Explanation/Reference:
QUESTION 3
Select and Place: Correct Answer:
Section: (none)Explanation
Explanation/Reference:
QUESTION 4
As a CCNA candidate, you are required to have a firm understanding of the OSI model. At which layers of the OSI model do Wide Area Networks operate in? Please drag the items to the proper locations.
Select and Place:
Correct Answer:
Section: (none)Explanation
Explanation/Reference:
A WAN is a data communications network that covers a relatively broad geographic area and that often uses transmission facilities provided by common carriers, such as telephone companies. WAN technologies generally function at the lower two layers of the OSI reference model: the physical layer and the data link layer as shown below.
Note: Occasionally WAN’s would also be considered to operate at layer 3, but since this question asked for only 2 choices, layers 1 and 2 are better choices.
QUESTION 5
Refer to the exhibit. Both switches are using a default configuration. Which two destination addresses will host 4 use to send data to host 1? (Choose two.)
A. the IP address of host 1
B. the IP address of host 4
C. the MAC address of host 1
D. the MAC address of host 4
E. the MAC address of the Fa0/0 interface of the R1 router
F. the MAC address of the Fa0/1 interface of the R1 router
Correct Answer: AF Section: (none) Explanation
Explanation/Reference:
QUESTION 6
Refer to the exhibit. SW1 and SW2 have default configurations. What will happen if host 1 sends a broadcast?
A. Hosts 2, 3, and 4 will receive the broadcast.
B. Hosts 1, 2, 3, and 4 will receive the broadcast.
C. Host 2 and the Fa0/0 interface of R1 will receive the broadcast.
D. Hosts 1, 2 and the Fa0/0 interface of R1 will receive the broadcast.
E. Hosts 1, 2, 3, 4 and interface Fa0/0 of R1 will receive the broadcast.
F. Hosts 2, 3, 4, and interfaces Fa0/0 and Fa0/1 of R1 will receive the broadcast.
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 7
A router has learned three possible routes that could be used to reach a destination network. One route is from EIGRP and has a composite metric of 20514560. Another route is from OSPF with a metric of 782. The last is from RIPv2 and has a metric of 4. Which route or routes will the router install in the routing table?
A. the OSPF route
B. the EIGRP route
C. the RIPv2 route
D. all three routes
E. the OSPF and RIPv2 routes
Correct Answer: B Section: (none)Explanation
Explanation/Reference:
QUESTION 8
Refer to the exhibit. The router has been configured with these commands: hostname Gateway interface FastEthernet 0/0 ip address 198.133.219.14 255.255.255.248 no shutdown interface FastEthernet 0/1 ip address 192.168.10.254 255.255.255.0
no shutdown interface Serial 0/0 ip address 64.100.0.2 255.255.255.252 no shutdown ip route 0.0.0.0 0.0.0.0 64.100.0.1 What are the two results of this configuration? (Choose two.)
A. The default route should have a next hop address of 64.100.0.3.
B. Hosts on the LAN that is connected to FastEthernet 0/1 are using public IP addressing.
C. The address of the subnet segment with the WWW server will support seven more servers.
D. The addressing scheme allows users on the Internet to access the WWW server.
E. Hosts on the LAN that is connected to FastEthernet 0/1 will not be able to access the Internet without address translation.
Correct Answer: DE Section: (none) Explanation
Explanation/Reference:
QUESTION 9
A company is installing IP phones. The phones and office computers connect to the same device. To ensure maximum throughput for the phone data, the company needs to make sure that the phone traffic is on a different network from that of the office computer data traffic. What is the best network device to which to directly connect the phones and computers, and what technology should be implemented on this device? (Choose two.)
A. hub
B. router
C. switch
D. STP
E. subinterfaces
F. VLAN
Correct Answer: CF Section: (none)Explanation Explanation/Reference:
QUESTION 10
For what two purposes does the Ethernet protocol use physical addresses? (Choose two.)
A. to uniquely identify devices at Layer 2
B. to allow communication with devices on a different network
C. to differentiate a Layer 2 frame from a Layer 3 packet
D. to establish a priority system to determine which device gets to transmit first
E. to allow communication between different devices on the same network
F. to allow detection of a remote device when its physical address is unknown
Correct Answer: AE Section: (none)Explanation
Explanation/Reference:
QUESTION 11
Refer to the diagram. Which three statements describe the router port configuration and the switch port configuration as shown in the topology? (Choose three.)
A. The Router1 WAN port is configured as a trunking port.
B. The Router1 port connected to Switch1 is configured using subinterfaces.
C. The Router1 port connected to Switch1 is configured as 10 Mbps.
D. The Switch1 port connected to Router1 is configured as a trunking port.
E. The Switch1 port connected to Host B is configured as an access port.
F. The Switch1 port connected to Hub1 is configured as full duplex.
Correct Answer: BDE Section: (none) Explanation
Explanation/Reference:
QUESTION 12
Which routing protocols will support the following IP addressing scheme? (Choose three.) Network 1 –
192.168.10.0 /26 Network 2 – 192.168.10.64 /27 Network 3 – 192.168.10.96 /27 Network 4 – 192.168.10.128 /30 Network 5 – 192.168.10.132 /30
A. RIP version 1
B. RIP version 2
C. IGRP
D. EIGRP
E. OSPF
Correct Answer: BDE Section: (none)Explanation
Explanation/Reference:
QUESTION 13
Refer to the partial command output shown. Which two statements are correct regarding the router hardware? (Choose two.)
A. Total RAM size is 32 KB.
B. Total RAM size is 16384 KB (16 MB).
C. Total RAM size is 65536 KB (64 MB).
D. Flash size is 32 KB.
E. Flash size is 16384 KB (16 MB).
F. Flash size is 65536 KB (64 MB).
Correct Answer: CE Section: (none) Explanation
Explanation/Reference:
QUESTION 14
The Ethernet networks connected to router R1 in the graphic have been summarized for router R2 as 192.1.144.0/20. Which of the following packet destination addresses will R2 forward to R1, according to this summary? (Choose two.)
A. 192.1.159.2
B. 192.1.160.11
C. 192.1.138.41
D. 192.1.151.254
E. 192.1.143.145
F. 192.1.1.144
Correct Answer: AD Section: (none) Explanation
Explanation/Reference:
QUESTION 15
The show interfaces serial 0/0 command resulted in the output shown in the graphic. What are possible causes for this interface status? (Choose three.)
A. The interface is shut down.
B. No keepalive messages are received.
C. The clockrate is not set.
D. No loopback address is set.
E. No cable is attached to the interface.
F. There is a mismatch in the encapsulation type.
Correct Answer: BCF Section: (none) Explanation
Explanation/Reference:
QUESTION 16
Which of the following describe private IP addresses? (Choose two.)
A. addresses chosen by a company to communicate with the Internet
B. addresses that cannot be routed through the public Internet
C. addresses that can be routed through the public Internet
D. a scheme to conserve public addresses
E. addresses licensed to enterprises or ISPs by an Internet registry organization
Correct Answer: BD Section: (none) Explanation
Explanation/Reference:
QUESTION 17
Refer to the exhibit. The network shown in the diagram is experiencing connectivity problems. Which of the following will correct the problems? (Choose two.)
A. Configure the gateway on Host A as 10.1.1.1.
B. Configure the gateway on Host B as 10.1.2.254.
C. Configure the IP address of Host A as 10.1.2.2.
D. Configure the IP address of Host B as 10.1.2.2.
E. Configure the masks on both hosts to be 255.255.255.224.
F. Configure the masks on both hosts to be 255.255.255.240.
Correct Answer: BD Section: (none) Explanation
Explanation/Reference:
QUESTION 18
A network associate is trying to understand the operation of the FLD Corporation by studying the network in the exhibit. The associate knows that the server in VLAN 4 provides the necessary resources to support the user hosts in the other VLANs. The associate needs to determine which interfaces are access ports. Which interfaces are access ports? (Choose three.)
A. Switch1 – Fa 0/2
B. Switch1 – Fa 0/9
C. Switch2 – Fa 0/3
D. Switch2 – Fa 0/4
E. Switch2 – Fa 0/8
F. Router – Fa 1/0
Correct Answer: ACD Section: (none) Explanation
Explanation/Reference:
QUESTION 19
Refer to the exhibit. Which destination addresses will Host A use to send data to Host B? (Choose two.)
A. the IP address of Switch1
B. the IP address of Router1 Fa0/0
C. the IP address of HostB
D. the MAC address of Switch1
E. the MAC address of Router1 Fa0/0
F. the MAC address of HostB
Correct Answer: CE Section: (none) Explanation
Explanation/Reference:
QUESTION 20
The network security policy requires that only one host be permitted to attach dynamically to each switch interface. If that policy is violated, the interface should shut down. Which two commands must the network administrator configure on the 2950 Catalyst switch to meet this policy? (Choose two.)
A. Switch1(config-if)# switchport port-security maximum 1
B. Switch1(config)# mac-address-table secure
C. Switch1(config)# access-list 10 permit ip host
D. Switch1(config-if)# switchport port-security violation shutdown
E. Switch1(config-if)# ip access-group 10
Correct Answer: AD Section: (none) Explanation
Explanation/Reference:
Worried about Cisco 640-802 pass results? Adopt most reliable way of exam preparation that is Cisco 640-802 Questions & Answers with explanations to get reliable high Cisco 640-802 pass result.Flydumps definitely guarantees it!